Page 1 of 1

Reinforcements Pack

Posted: Fri Jun 01, 2018 10:40 pm
by Rebel Yell
I have 1.0.35 and the Broken Alliance and everything plays fine, but I ran the Reinforcement Pack installer and it ran and finished normally, but the Janus and Berserker and the other ships are not appearing in skirmish.

What do I need to do different to get those ships back?

Re: Reinforcements Pack

Posted: Sat Jun 02, 2018 1:26 pm
by Asap
Same for you (viewtopic.php?f=483&t=85758),
install the game in that order and you will get all those ships back:

1. Install "Battlestar Galactica Deadlock" version 1.0.35
2. Then install the "Reinforcement Pack"
3. Finally you install "Battlestar Galactica Deadlock - The Broken Aliance"

Re: Reinforcements Pack

Posted: Sat Jun 02, 2018 9:51 pm
by Rebel Yell
That did it, thanks.

Re: Reinforcements Pack

Posted: Sun Jun 03, 2018 7:59 am
by Asap
You are welcome, @Rebel Yell :)

Re: Reinforcements Pack

Posted: Tue Jun 05, 2018 11:48 pm
by SiegeRollout
Asap wrote:You are welcome, @Rebel Yell :)
didnt work for me either. I've now reinstalled several times, and no joy. I'm completely stuck & frustrated

Re: Reinforcements Pack

Posted: Wed Jun 06, 2018 1:21 am
by Asap
SiegeRollout wrote:
Asap wrote:You are welcome, @Rebel Yell :)
didnt work for me either. I've now reinstalled several times, and no joy. I'm completely stuck & frustrated
Do not use the installer of version 1.0.35 for the "Reinforcement Pack" and for "Battlestar Galactica Deadlock - The Broken Alliance", install these two separately.

Re: Reinforcements Pack

Posted: Wed Jun 06, 2018 1:41 pm
by SiegeRollout
Asap wrote:
SiegeRollout wrote:
Asap wrote:You are welcome, @Rebel Yell :)
didnt work for me either. I've now reinstalled several times, and no joy. I'm completely stuck & frustrated
Do not use the installer of version 1.0.35 for the "Reinforcement Pack" and for "Battlestar Galactica Deadlock - The Broken Alliance", install these two separately.
I'm still not following what I'm doing incorrectly. I did the following steps:
1) Complete uninstall
2) Reboot Computer
3) Run DeadLock 1.0.35 installer (latest version). I put in all 3 product keys at the end as instructed.
4) Run Reinforcement Pack installer (1.0.20, the only version of that installer I have). Serial key accepted at end of installer
5) Run BrokenAlliance installer (1.0.35). Serial key accepted at end of installer

I'm not clear what you mean by "don't use installer of version 1.0.35 for Reinforcement Pack". When I try this all over again, should I not enter my activation keys in step #3 for Reinforcement & Broken Alliance. It asks for them again in step #4 and Step #5.

Appreciate the help. I'm not getting anything but platitudes from the Support ticket I opened.

Re: Reinforcements Pack

Posted: Wed Jun 06, 2018 2:06 pm
by Asap
SiegeRollout wrote: 1) Complete uninstall
2) Reboot Computer
3) Run DeadLock 1.0.35 installer (latest version). I put in all 3 product keys at the end as instructed.
4) Run Reinforcement Pack installer (1.0.20, the only version of that installer I have). Serial key accepted at end of installer
5) Run BrokenAlliance installer (1.0.35). Serial key accepted at end of installer

I'm not clear what you mean by "don't use installer of version 1.0.35 for Reinforcement Pack". When I try this all over again, should I not enter my activation keys in step #3 for Reinforcement & Broken Alliance. It asks for them again in step #4 and Step #5.

Appreciate the help. I'm not getting anything but platitudes from the Support ticket I opened.
Try not to put anything of "Reinforcement Pack" and "The Broken Alliance" in the installer of version 1.0.35 "Battlestar Galactica Deadlock"(this is what I mean). Install it all one by one. I think, you don't need to reboot your computer, just uninstall the game. It worked for me and I hope it will work for you, as well. :)

Re: Reinforcements Pack

Posted: Wed Jun 06, 2018 2:24 pm
by SiegeRollout
Asap wrote:
SiegeRollout wrote:
Try not to put anything of "Reinforcement Pack" and "The Broken Alliance" in the installer of version 1.0.35 "Battlestar Galactica Deadlock"(this is what I mean). Install it all one by one. I think, you don't need to reboot your computer, just uninstall the game. It worked for me and I hope it will work for you, as well. :)
Yep. I did another uninstall/reinstall. This time, I didnt input the product keys for Reinforce/BA when doing Deadlock install, even though it prompts you to do so. Slitherine really needs to do some basic QA of their installer, that's a pretty substantial bug.

Thx again for the assistance!